Double Glazing Door Lock Repairs
Are your uPVC window or door mechanism not working properly? Perhaps the handles on your uPVC windows and doors aren't aligned properly or are difficult to operate.
You will lose energy in the event that your double-glazed doors fail to perform as they should. This can also increase the chance of burglary. Owen the Locksmith can repair your door lock for a reasonable cost.
Snapped Key
It can be a hassle when a key snaps into a lock. It could also be a security risk, as the door may not be locked and could leave you vulnerable to burglars. There are a few quick solutions you can use to resolve the issue and get your door working again.
First, remember to stay calm. If you get scared and start playing around with your keys, you might just end up pushing the broken piece of the key even further into the lock, thereby making the situation worse.
Then spray WD-40 or a different penetrating oil into the lock to aid in making the broken piece to slide out more easily. You can also use the screwdriver to break up any pieces that are stuck. If you have a part of the key that's stuck out then grab it using a paperclip or other thin metal object and pull it. Both methods work, but be careful not to push the broken key piece further into the keyway.
Some paperclips have grooved edges, which can work in a pinch as hook extractors and Jigsaw blades also work for this use. If you don't have any of these, you can bend a hook with needle-nosed pliers. Also, a pair tweezers is a good way to grasp and pull out the last bit of the broken key.
If you're unable to pull the broken piece of the key out, you can try using a lock de-icer. It's usually found in most hardware stores. It works by freezing any moisture or ice that may be inside the lock.
If none of these solutions work, it might be time to consult a locksmith. double glazing window repairs can fix problems such as broken handles or snapped keys using uPVC locks and door mechanisms. They can also reconfigure your double glazing door mechanisms to allow them to operate more easily. Book a double glazing repair through us online, or give us a phone call to discuss your needs.
Broken Cylinder
A broken cylinder is an extremely risky security issue. A locksmith professional can repair the cylinder. A locksmith must tap the cylinder in order to fix it. This can be accomplished with a hammer or other tool. The best method is to employ a wire or long match. The match or wire's end close to the keyway. After that, the locksmith will hit the lock to break it open. This is superior to using the hammer, which could damage the lock.
The most frequent cause of cylinder head cracks is overheating. This can occur when the block and the cylinder head are made from different metals such as cast-iron and aluminium. When different metals are heated and cool at different rates, it can create hotspots in the local area that expand faster than the rest of the cylinder head, thus leading to cracks.
Another reason that could cause cylinder cracks is corrosion. If the cylinder head as well as cylinder block are not properly maintained, this can lead to rusting or corrosion that could cause them to expand at a a higher rate than they should. This can lead to cracks as time passes.
If your uPVC door or window lock is stiff or requires lots of pressure to turn, it can be caused by many things. A faulty locking mechanism, misalignment or an old handle are the most common reasons for this issue.
This is a straightforward and affordable fix that the majority of homeowners with double glazing can perform. A professional locksmith will typically be able to solve this problem within an hour of arriving at your home. They can replace the locking mechanisms, or change the window handles and change the gearboxes, depending on your specific needs. A professional locksmith can always advise you on the most cost-effective solution for your home. They can even recommend upgrades to 3 Star security Euro cylinders, TS007, that will provide an extra layer of security against burglars. This is a small price to pay for the security that comes with knowing your uPVC doors are secure.
Broken Handle
Window handle locks have complex mechanisms that become less effective with age and use, so it's no surprise they occasionally break. If yours breaks it may be difficult to pinpoint the cause of the problem and make sure you fix it correctly.
Fixing your broken handle, regardless of whether it's the internal locking mechanism or latch will increase the security of your uPVC door and stop draughts. It is costly to replace or repair the handle in a way that isn't done correctly. It can also harm the frame and lock of your door.
With the window in the open position, loosen the screw holding the handle using a screwdriver. The screw should be located on the inside of the backplate. It is typically covered by a screw cap for aesthetic purposes. It is important to not be able to replace any internal parts of the handle, such as the plates and levers on either side. Keep them in the same order to make it easier to replace them if needed.
Then, rotate the handle to make it 90 degrees to the window frame. Finally, loosen the screw at the back of the handle that holds it to the internal spindle using another screwdriver. Once this is loose, you should be capable of pulling the handle off and pull off the damaged spindle. Replace this with a new one, ensuring it's the same length as the previous one (you can typically find these on the internet or at hardware stores) and screw it securely into the correct position. Be cautious not to overtighten because this could damage the handle or the window frame.
Check that the new handle is installed, then close and test the handle. The hope is that it will function smoothly and you'll be able to open your window again.
While you're working on the handle, make sure to check your uPVC windows are shut properly. If they're not cause damp and draughts inside your home, as and also affecting your home's energy efficiency. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window frames to ensure they are able to shut properly.
Broken Spindle
It is quite common that the spindle in the handle is broken, not the handle itself. This is particularly common with uPVC tilt-and-turn windows. These types of windows require a handle that is a lock mechanism that is located in the frame of the window. The handle is connected to a central rod that activates a series of mushroom-shaped locking cams that secure the window frame keep. If the dead latch mechanism fails to open when the handle has been turned, it is likely the spindle is damaged. This could be a problem that is frustrating.
There are ways to fix this issue. A reputable locksmith will be able to quickly and effectively fix this problem. They will be able to take apart the window handle using a tool that can remove the wheel portion of the mechanism, where the spindle goes. This is done without damaging the handle or causing any other damage to the frame of the window.
After removing the wheel the technician can inspect the spindle to determine the cause of the break. This involves breaking the spindle into its individual parts and meticulously noting their general condition as in addition to any specific areas of damage or excessive wear. This procedure is typically performed by technicians in a clean environment.
Next, clean the damaged spindle. This will help remove any debris or dirt that may be obstructing it from working normally. The spindle may then be repaired or replaced. If it's being replaced, the technician will need the dowel that is similar in size to the original and drill mating holes in both pieces of the spindle. This will ensure that the spindle is perfectly matched with the handle.
If the damaged spindle is beyond repair, it could be necessary to replace it completely. Home centres sell generic replacements. However, If the style of your window is unusual then you will need to find a woodworker or cabinet maker who can make the exact model for you. Once the spindle has been installed, it is connected to the handle. Line up the screw holes on the handle to the existing screws in the frame. Once the handle is firmly seated, you can operate your uPVC windows.